CCS 機械軸承精密直驅轉臺 | CCS Mechanical-Bearing Direct-Drive Rotary Stage
Aerotech的CCS系列轉臺集成抓獲彈簧夾為范圍廣泛的材料和應用提供自動材料處理能力。
CCS Series Specifications
| Model | CCS130DR-160 | CCS190DR-240 | CCS190DR-260 | |
|---|---|---|---|---|
| Travel | 360° Continuous | |||
| Accuracy | Uncalibrated | 50 arc sec | ||
| Calibrated(1) | 5 arc sec | |||
| Bidirectional Repeatability | 2 arc sec | |||
| Maximum Speed(2) | 1000 rpm | 600 rpm | ||
| Aperture(3) | 7.9 mm (Dry); 3 mm (Wet) | 13 mm | 26.5 mm | |
| Maximum Torque (Continuous) | 0.64 N?m | 2.85 N?m | 5.06 N?m | |
| Load Capacity(4) | Axial | 2 kg | 10 kg | 15 kg |
| Radial | 0.5 kg | 5 kg | 10 kg | |
| Moment | 0.75 N?m | 6 N?m | 12 N?m | |
| Rotor Inertia (Unloaded) | 0.0004 kg?m2 | 0.0039 kg?m2 | 0.0051 kg?m2 | |
| Stage Mass | 3.1 kg | 12.0 kg | 14.1 kg | |
| Material | Hardcoat/Anodized Aluminum; Hardened Stainless Steel (Collet Chuck) | |||
| MTBF (Mean Time Between Failure) | 10,000 Hours | |||
| Collet Type | Type D (Louis Levin & SonsTM) | 3C | 5C | |
| Collet Runout(5) | <30 μm | <25 μm | <20 μm | |
| System Air Pressure(6)(7)(8) | 100 psig | 20-100 psig | 20-80 psig | |
- Calibrated accuracy requires the use of Aerotech controls and angular programming units.
- Maximum speed listed is stage and motor dependent (assuming a 340 V bus). Actual speed may be lower due to motor back emf. Consult Aerotech for more details.
- The CCS130DR-160 maximum tube diameter is reduced to 6.7 mm for dry cutting with the -WC option.
- Maximum loads are mutually exclusive. Loading limits are due to the collet chuck mechanism. Contact Aerotech directly if part load requirement exceeds specifications.
- TIR of precision gage pin in an ultra-precision collet. Measured 3 mm away from collet face at 80 psig applied air pressure for CCS130DR. Measured 6 mm away from collet face at 40 psig applied air pressure for CCS190DR.
- The CCS190DR-260 and CCS190DR-240 contain a double-acting collet mechanism that requires air to open and close the collet chuck. Aerotech recommends compressed air filtered to 0.25 micron particle size or better.
- The CCS130DR-160 contains a collet chuck mechanism that is normally-open. Collet mechanism requires air to close collet chuck. Air supply must be dry (0o F dew point), oil-less air or 99.99% pure nitrogen. Air or nitrogen must be filtered to 0.25 micron particle size or better.
- Exceeding the maximum system air pressure on the CCS190 stages is not recommended and could cause damage and/or performance degradation.
Dimensions
-
CCS130DR-160
-
CCS190DR-240
-
CCS190DR-260
Ordering Information
Ordering Example
| CCS130DR-160 | -D | -RE-AS | -WC | -RINGSEAL-1.00MM | -M-0100 | -PN |
Ordering Options
| Series | Collet Chuck | Encoder | Cutting Configuration | Ring Seals | Collets | Pneumatics |
|---|---|---|---|---|---|---|
| CCS130DR-160 | -D | -RE-AS |
-DC -WC |
-RINGSEAL-x.xxMM |
-M-xxxx -EF-xxxxx |
-PN -FD |
CCS130DR-160 Rotary Stage with Dead-Length Collet
| Option | Description |
|---|---|
| CCS130DR-160 | Direct-drive rotary stage with integrated D-style dead-length collet chuck |
Collet Chuck
| Option | Description |
|---|---|
| -D | Normally open, air actuated D-style collet chuck |
Encoder
| Option | Description |
|---|---|
| -RE-AS | 1 Vpp amplified sine output; 3600 cycles per rev |
Cutting Configuration
| Option | Description |
|---|---|
| -DC | Dry cutting |
| -WC | Wet cutting |
Ring Seals
| Option | Description |
|---|---|
| -RINGSEAL-x.xxMM | Wet-cut seal sized for x.xx diameter tubing; consult Aerotech for available sizes |
Collets
| Option | Description |
|---|---|
| -M-xxxx | Levin D-style collets sized for xxxx diameter tubing (0.1 mm to 7.9 mm); consult Aerotech for the available sizes |
| -EF-xxxxx | Levin D-style collets sized for xxxxx diameter tubing (1/64" to 5/16"); consult Aerotech for the available sizes |
Pneumatics
| Option | Description |
|---|---|
| -PN | Solenoid valves and relays for collet-chuck actuation |
| -FD | Filter drier assembly to ensure clean dry air to the collet chuck |
Ordering Example
| CCS190DR-240 | -3C | -RE-AS | -M-0100 | -PN | ‑WRENCH |
Ordering Options
| Series | Collet Chuck | Encoder | Collets | Pneumatics | ‑WRENCH |
|---|---|---|---|---|---|
|
CCS190DR‑240 CCS190DR‑260 |
-3C (-240 only) -5C (-260 only) |
-RE-AS |
‑M‑xxxx ‑EF‑xxxxx ‑ED‑xxxx |
-PN -F |
-WRENCH |
CCS190DR-240/-260 Rotary Stage with Dead-Length Collet
| Option | Description |
|---|---|
|
CCS190DR-240 |
Direct-drive rotary stage with integral pneumatic captive collet chuck |
| CCS190DR-260 | Direct-drive rotary stage with integral pneumatic captive collet chuck |
Collet Chuck
| Option | Description |
|---|---|
| -3C | Double acting, air-actuated 3C collet chuck |
| -5C | Double acting, air-actuated 5C collet chuck |
Encoder
| Option | Description |
|---|---|
| -RE-AS | 1 Vpp amplified sine output; 13,600 cycles per rev |
Collets
| Option | Description |
|---|---|
| -M-xxxx | 3C collets sized for xxxx diameter tubing (0.4 mm to 13 mm); consult Aerotech for the available sizes (-240 only) |
| -EF-xxxxx | 3C collets sized for xxxxx diameter tubing (1/64" to 1/2"); consult Aerotech for the available sizes (-240 only) |
| -ED-xxxx | 3C collets sized for xxxx diameter tubing (0.070" to 0.400"); consult Aerotech for the available sizes (-240 only) |
| -M-xxxx | 5C collets sized for xxxx diameter tubing (0.4 mm to 27 mm*); consult Aerotech for the available sizes (-260 only) |
| -EF-xxxxx | 5C collets sized for xxxxx diameter tubing (1/64" to 1-1/16"*); consult Aerotech for the available sizes (-260 only) |
| -ED-xxxx | 5C collets sized for xxxx diameter tubing (0.016" to 1.030"*); consult Aerotech for the available sizes (-260 only) |
-
*Thru capacity only up to 25.5 mm (1.004").
Pneumatics
| Option | Description |
|---|---|
| -PN | Solenoid valves and relays for collet-chuck actuation |
| -F | Filter assembly to ensure clean air to the collet chuck |
Tooling
| Option | Description |
|---|---|
| -WRENCH | Face wrench to change collet |